From analogue-request@magnus.acs.ohio-state.edu Tue Oct 26 12:05:54 1993 Received: from condor.CC.UMontreal.CA by eole.ERE.UMontreal.CA (920330.SGI/5.17) id AA18089; Tue, 26 Oct 93 12:05:52 -0400 Received: from quark.magnus.acs.ohio-state.edu by condor.CC.UMontreal.CA with SMTP id AA24244 (5.65c/IDA-1.4.4 for dionf@ERE.UMontreal.CA); Tue, 26 Oct 1993 12:05:50 -0400 Received: by quark.magnus.acs.ohio-state.edu (5.65/3.910213) id AA13915; Tue, 26 Oct 93 11:58:24 -0400 Errors-To: analogue-request@magnus.acs.ohio-state.edu Sender: analogue-request@magnus.acs.ohio-state.edu Received: from husc3.harvard.edu by quark.magnus.acs.ohio-state.edu (5.65/3.910213) id AA13897; Tue, 26 Oct 93 11:58:19 -0400 Received: from HUSC15.HARVARD.EDU by HUSC15.HARVARD.EDU (PMDF V4.2-13 #4724) id <01H4KFVQY6G0934QNF@HUSC15.HARVARD.EDU>; Tue, 26 Oct 1993 11:58:56 EDT Date: Tue, 26 Oct 1993 11:58:56 -0400 (EDT) From: SCHOENB@HUSC15.HARVARD.EDU Subject: 6trak modes To: analogue@magnus.acs.ohio-state.edu Message-Id: <01H4KFVQZIO2934QNF@HUSC15.HARVARD.EDU> X-Vms-To: MAILER%"analogue@magnus.acs.ohio-state.edu" Mime-Version: 1.0 Content-Type: TEXT/PLAIN; CHARSET=US-ASCII Content-Transfer-Encoding: 7BIT Status: RO SCI 6TRAK MODE NOTES The 610 powers-up in Omni Mode (Mode 1). The Channel Number can be changed from the front panel (see Parameter 36. under CODED FUNCTIONS). The Channel Number is ignored while in Omni On Mode, except for the Omni Off command. Mono On commands are ignored in Omni On rnode (i.e., Mode 2 is not recognized). On power-up, only Note On/0ff and Program Dump messages are sent and received. Wheel changes and program changes can be enabled from the front panel (see CODED FUNCTIONS). When Omni Off is selected (Mode 3), all messages without the Basic Channel number are ignored. When Omni Off and Mono On (Mode 4), the 6;0 will assign one each of its six voices to channels N to N+5, where N is the current basic channel. Note that this will normally mean channels 3 - 8 (n = 2 - 7). Note also that the basic channel must not be set above 11, to allow room for six voices. When Mode 4 is selected, it will automatically be set to 11 if the channel is higher. If Omni On is selected while Mono is On, Poly On/Mono Off will automatically be executed. Basic Channel number can be changed by selecting PARAMETER #36, and adjusting for a value for 1 - 16. The channel number is non-volatile--it will remain as selected even through power off. The Basic Channel is set to 3 at the factory. Note that the Basic Channel number is sent with transmitted data. CODED MIDI FUNCTIONS While holding the RECORD switches, press the indicated SELECT switch. CONTROL RECORD is on the right. TRACK RECORD is on the left. Modes Mode l--Omni On/Mono Off TRACK RECORD/SELECT 1 Mode 3--0mni off/Mono Off TRACK RECORD/SELECT 3 Mode 4--0mni Off/Mono On TRACK RECORD/SELECT 4 Dumps Dump Current Sequences and Stacks CONTROL RECORD/SELECT 0. Dump Current Program CONTROL RECORD/SELECT 2. This sends 16 bytes of the program data of the program currently displayed. Dump 100 Programs TRACK RECORD/SELECT 9. Control Options Change Channel # Select PARAMETER #36. Switch VALUE on and adjust VALUE knob to select desired channel (l - 16). Note that in Mode 4, channel 11 is the maximum usable channel. Channel number can also be changed remotely by a Select Double Mode command over MIDI. Select Double Mode TRACK RECORD/SELECT 2. For 610/610 or 610/210. In the master instrument, enables wheel changes, voice-to- voice program changes and note information (Mode 4). Selects Channel 11 if set to higher. Sends SYS EX 7B Double Mode Command to slave, to effect similar changes. Select MIDI Clock Input Turn SPEED knob fully counterclockwise. Enable/Disable Program Change CONTROL RECORD/SELECT 1. This toggles Program Change over MIDI, send and receive. On power-up, Program Change is disabled. Enable/Disable Wheels and Parameter Changes CONTROL RECORD/SELECT 4. This toggles PITCH and MOD wheel send/receive and Parameter changes (receive only) over MIDI. On power-up, disabled. Local On TRACK RECORD/SELECT 7. Enables the 610's keyboard, switches, and wheels. Enabled on power-up. Local Off TRACK RECORD/SELECT 8. Disconnects the keyboard, wheels, and switches from the sound-generating circuitry. The information will be sent over MIDI, but only MIDI received data will play the 610. This code will be ignored when the sequencer, arpeggiator, or stack mode is on. ================================================================= enjoy...lloyd schoenbach schoenb@husc15.harvard.edu